Search results for: 'Kit-Shower Valve Tahoe Mattee black'

Low Profile, 2.25" (5.7cm) extension from wall

Stainless Steel & Brass construction

Square Base with Round Bar

Easily mounts to any wall surface

Low Profile, 2.25" (5.7cm) extension from wall

Stainless Steel & Brass constuction

Round Base with Round Bar

Easily mounts to any wall surface

Low Profile, 2.25" (5.7cm) extension from wall

Stainless Steel & Brass constuction

Round Base with Round Bar

Easily mounts to any wall surface

Constructed of Low Lead solid Brass for durability

cUPC certified to meet both the American and Canadian Uniform Plumbing Codes

Brass Cartridge

Easy to install

90° swiveling spout

For either cold or hot water, Red/Blue indicators included

This wire is the same wire used by the RV Manufactures in 12 Volt DC circuits.

This is the wire we recommend, its colors match the UltraHeat power leads for ease in wiring connections,  and also meets the minimum gauge wire requirements when used with the UltraHeat switch kits.  

This wire is the same wire used by the RV Manufactures in 12 Volt DC circuits.

This is the wire we recommend, its colors match the UltraHeat power leads for ease in wiring connections,  and also meets the minimum gauge wire requirements when used with the UltraHeat switch kits. 

GP-1000
Modified Sine Wave Inverter
1000 Watts -12 volt
Length: 13.5 Inches (34.29 cm)
Width: 12 Inches (30.48 cm)
Height: 3.5 Inches (8.89 cm)
Weight: 4.2 lbs (1.91 kg)
Go Power! 1000-Watt Modified Sine Wave Inverter takes in 12 Volt DC power and converts it to AC household power to run loads up to 1000-Watt of continuous power. This inverter comes with two AC outlets and can be hooked up to the batteries using GP-DC-KIT2 and can surge to 1300-Watt as well as contains all instructions.

To be wired in parallel with other relay coils within the Master Control Circuit  

Coil - 12VDC

Contacts - 30A @ 120/277 VAC

                    20A @ 28 VDC (low voltage)

Includes:

3- 120 VAC illuminated switches

1 - labeled switch platewith raised mounting bezel
9 - quick slide female connectors,
4 - mounting plate screws

Each switch is rated for 20 Amps maximum.

Includes:

1- 120 VAC illuminated switch
2 - Labeled switch plates
(1-Tank, 1-Pipe/Elbow)
1 - Raised Mounting Bezel
3 - quick slide female connectors,
2  -mounting plate screws

Switch is rated for 20 Amps maximum

Includes:

1 - 13.5 VDC illuminated switch
2 - Labeled switch plates
(1-Tank Heater, 1-Pipe/Elbow Heater)
1 - Raised Mounting Bezel
3 - quick slide female connectors,
2 - mounting plate screws

Switch is rated for 20 Amps maximum

Model: BP:LT0143
Light Controller
Length:4.5 Inches (11.43 cm)
Width: 2.875 Inches (7.30 cm)
Height: 1 Inch (2.54 cm)
Weight: .2 lb (.091kg)
SecuRemote is a device that when connected to your LIT (Light Integrated Trim) LED lighting allows you to power on/off or even dim your lights using your smart phone.The SecuRemote app works with all three major smartphone platforms including iPhone, Android and BlackBerry.SecuRemote uses unique technology to deliver powerful communication, authentication and functiionality to your LIT products and also home entry doors, garage doors and electronic gates.SecuRemote blends seamlessly into your lifestyle, bringing unprecedented convenience, control and security to you and your family.

Stainless Steel & Brass constuction

Round Base with Round Bar

Easily mounts to any wall surface

Length: 48ft.,  15 suspended sockets. Spacing: 3ft.

Plug to the first socket: 3ft. Last socket to tech tail: 3ft.

Cable: Black,  SJTW 2 wire, 18AWG.

Includes: 18pcs S14-11Watt Incandescent bulbs, 120 VAC, Clear and Dimmable, Warm White 2700 Kelvin (Warm White)

Length: 48ft.,  15 suspended sockets. Spacing: 3ft.

Plug to the first socket: 3ft. Last socket to tech tail: 3ft.

Cable: Black,  SJTW 2 wire, 18AWG.

Includes: 15pcs S14-2Watt LED bulbs, 120 VAC, Clear and Dimmable, 2700 Kelvin (Warm White)

Dimensions: 7.87"H x 4.875"W x7.25"D Packaged

Shipping Weight: 0.62 lbs Packaged

Color: Black/Orange

Max Capacity: up to 30 lbs (drywall/stud)

2 Tornado fasteners to install into wall included

Model:PNH:TM-22-WH22
White Tire Mount for 22' Fiberglass Flagpole
Length: 30.25 inches (76.84 cm)
Base Width: 3 inches (7.62 cm)
Tube Height:14 inches (35.56 cm)
Diameter: 2 inches (5.08 cm)
Weight: 5 pounds (2.27 kg)
This unique mount can be used on virtually any vehicle tire. Comes with a black shiny powder coat finish. Simply place the mount on the ground and drive up on it. Thates all it takes! No tools required. Can also be used under trailer stabilizing or tongue jacks. This mount is designed for the 22e heavy-duty fiberglass flag pole. Made in America.