Search results for: 'Elbow Heater 3" 13.5v'

Includes:

3- 13.5VDC illuminated switches

1 - labeled switch platewith raised mounting bezel
9 - quick slide female connectors,
4  -mounting plate screws

Each switch is rated for 20 Amps maximum.

Includes:

3- 120 VAC illuminated switches

1 - labeled switch platewith raised mounting bezel
9 - quick slide female connectors,
4 - mounting plate screws

Each switch is rated for 20 Amps maximum.

Includes:

5- 13.5VDC illuminated switches,
1 - labeled (Fresh, Gray, Black) 5 gang switch plate with raised mounting bezel
15 - quick slide female connectors,
4 - mounting plate screws
2 - blanks (to cover switchcutouts if all 5 switches are not used)

Each switch is rated for 20 Amps maximum

Vessel Sink, Dimensions: 14.25 x 9.84 x 5.12 Inches (362 * 250 * 130mm), Smoke Inside with Matte Black Exterior, Tempered Glass, cUPC.

Includes:

1- 120 VAC illuminated switch
2 - Labeled switch plates
(1-Tank, 1-Pipe/Elbow)
1 - Raised Mounting Bezel
3 - quick slide female connectors,
2  -mounting plate screws

Switch is rated for 20 Amps maximum

Glass Vessel Sink, 12 x 12 x 4.5 Inches (305 * 305 * 114.3 mm), T12 Thickness, Silver Ring, cUPC.

Model: BP:LT0106
Strip Connector Set - 90c Flat Corner
Length: .375 Inches (.952 cm)
Width: .375 Inches (.952 cm)
Height: .188 Inch (.476 cm)
Weight: .05 lb (.023 kg)
Connecting LED strips to any desired custom length while maintaining the exact LED spacing is easy. No more soldering or ugly gaps between strip connections. You can cut and splice multiple LED strips to form the exact length you desire by using the specially designed Strip Wire and Connectors. The connectors work with all three types of strips (shielded LED, non-shielded LED, and Strip Wire). You can bring low voltage power to your LIT application by using the power adapter(s) (one adapter per 32' LED length) and the Strip Wire. These are safe, low voltage flat wires that are easy to conceal.

Model: BP:LT0104
Strip Connector Set - Straight
Length: .375 Inches (.952 cm)
Width: .375 Inches (.952 cm)
Height: .188 Inch (.476 cm)
Weight: .05 lb (.023 kg)
Connecting LED strips to any desired custom length while maintaining the exact LED spacing is easy. No more soldering or ugly gaps between strip connections. You can cut and splice multiple LED strips to form the exact length you desire by using the specially designed Strip Wire and Connectors. The connectors work with all three types of strips (shielded LED, non-shielded LED, and Strip Wire). You can bring low voltage power to your LIT application by using the power adapter(s) (one adapter per 32' LED length) and the Strip Wire. These are safe, low voltage flat wires that are easy to conceal.

GP-1000
Modified Sine Wave Inverter
1000 Watts -12 volt
Length: 13.5 Inches (34.29 cm)
Width: 12 Inches (30.48 cm)
Height: 3.5 Inches (8.89 cm)
Weight: 4.2 lbs (1.91 kg)
Go Power! 1000-Watt Modified Sine Wave Inverter takes in 12 Volt DC power and converts it to AC household power to run loads up to 1000-Watt of continuous power. This inverter comes with two AC outlets and can be hooked up to the batteries using GP-DC-KIT2 and can surge to 1300-Watt as well as contains all instructions.

Includes:

1 - 13.5 VDC illuminated switch
1 - switch plate labeled 'Gate Valve Heater'
1 - Raised Mounting Bezel
3 - quick slide female connectors,
2 - mounting plate screws

Switch is rated for 20 Amps maximum